Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
HeatShield Chimney Cleaning in Berthoud, CO
We provide independent HeatShield service across Berthoud, and we’re not affiliated with, sponsored by, or authorized by HeatShield. What makes our HeatShield work here different is the wood. Berthoud sits at the edge of the foothills along the Little Thompson River valley, where a lot of homes burn whatever is on hand through long, windy winters, and the creosote that builds from that wood is what damages HeatShield surfaces faster than almost anything else. Our technicians have up to 15 years of experience, and we work only on chimneys. Call (833) 740-1407. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Why Berthoud Residents Choose Us for HeatShield Service
HeatShield products are specified systems, not a bucket of mortar. ArmorFlex, TherMix, and the Resurfacer each have their own mixing, troweling, and cure requirements, and an installer who doesn’t work with them regularly gets the ratios wrong or skips the flue-sizing math. We work with them often enough to know the difference between a lining that will hold and one that will fail in two winters.
That matters more in Berthoud than in a lot of places. Half the calls we take here come from rural ranchettes and converted farmhouses where the chimney has been patched by someone who didn’t understand what was already inside it. We come out, look at what’s actually there, and tell you plainly whether the existing HeatShield surface is worth saving.
One call covers the sweep, the inspection, and the repair. No handoffs, no second company following up on what we found. If you’ve been quoted a full reline and want a second look, we’re happy to provide it. You can read more about how we approach HeatShield work, and you can see how we serve the wider Berthoud area before you book.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common HeatShield Chimney Cleaning Problems We Solve in Berthoud
These are the specific failures we run into on HeatShield surfaces in this part of the Front Range, and why each one tends to show up here.
- ArmorFlex adhesion and insulation failure after freeze-thaw cycling. Exterior masonry chimneys in Berthoud go through repeated freeze-thaw swings, and that cycling works on the bond between an ArmorFlex lining and the flue wall. When water gets behind it and freezes, you get cracking and separation at the liner-to-flue joint. It doesn’t always announce itself, which is why the camera inspection matters.
- Glaze-stage creosote baked onto a HeatShield surface. On rural acreage properties, homeowners burn green or locally-cut pine, and glaze-stage creosote builds fast. That hard, shiny layer can hide spalling underneath and it has to come off completely before any resurfacing is valid. Sweeps in Berthoud see this far more than crews working the gas-heavy suburban flues in nearby Longmont or Loveland.
- Crowns and flashings chewed up by hail and wind. Tall, exposed exterior chimneys take the spring hail and wind straight on. Once the crown degrades, water migrates behind the lining and undermines TherMix or Resurfacer adhesion from the inside out.
- Misfired or unlined flues that were never sized for the appliance. Wood stoves and inserts get added after the fact, and a HeatShield reline that wasn’t sized for the actual appliance leads to continued creosote accumulation and stress on the liner. Sizing math isn’t optional.
- Aftermarket liners and generic refractory mortars used in a previous repair. We see patches done with materials that don’t match the specified cure and thickness of the HeatShield system. They can look fine for a season and then fail. We’ll tell you what’s in there and what it means.
HeatShield Service in Berthoud: What Local Conditions Mean for Your Equipment
The rural acreage properties outside town limits are where HeatShield work gets interesting. Homeowners there often burn whatever wood is on hand, including green or pine cut on their own land, and that builds creosote quickly. We routinely find glaze-stage creosote in stoves and inserts on these properties, a condition that’s far less common on the gas-heavy suburban flues in nearby Longmont and Loveland. Glaze-stage creosote is rock-hard and bonded tight, and it can degrade a HeatShield lining underneath it while looking like nothing more than a dirty flue. It has to be removed aggressively and completely before any resurfacing or TherMix repair is valid. Sweeping past it and coating over it just seals the problem in. So on properties off Highway 56 and out along Mountain Avenue, we start with the creosote, not with the product. Once the flue is clean, the camera shows what the lining actually looks like, and that’s when the conversation about repair starts.
HeatShield Models & Products We Service in Berthoud
We service the full range of HeatShield products used in masonry chimneys: ArmorFlex cast-in-place refractory linings, TherMix insulating refractory cement for relining and crown work, the Resurfacer for trowel-on repair of damaged flue liners, and the Crown Coat and Crown Repair products for masonry crowns. When we install, we use genuine HeatShield materials for anything structural, because aftermarket liners and generic refractory mortars don’t match the specified cure and thickness of the system. Where a lining is sound but the flue is just creosote-staged or lightly spalled, honest cleaning and spot resurfacing beats a full reline. Replace when the flue is cracked through, oversized, or the crown and flashing can’t be made watertight. We’re an independent HeatShield service provider, not manufacturer-affiliated or authorized, and we’re not a dealer. We repair, install, and service these systems with quality parts that fit them.
See the difference
Before
After
Before
After
Before
AfterHeatShield Service Pricing in Berthoud
Cost depends on what’s actually in the flue, so the written estimate is what sets the final price. Typical ranges:

- Standard sweep and Level 1 inspection: $150 to $300
- Level 2 camera inspection: $200 to $450
- Glaze-stage creosote removal: $300 to $700
- Crown repair: $250 to $600
- Resurfacer spot repair: $400 to $900
- TherMix reline: $2,500 to $6,000
- Full ArmorFlex reline: $4,000 to $9,000
The estimate is free and includes a camera inspection with photos you can see for yourself. We’ll tell you exactly what we found and exactly what it costs to fix it, before any work begins. Call (833) 740-1407 for an exact quote.
Serving Berthoud, CO – Our Local Coverage Area
We serve Berthoud and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – HeatShield Chimney Cleaning in Berthoud
Not necessarily. Glaze-stage creosote often sits on top of a lining that’s still structurally sound underneath. The only way to know is to remove the creosote completely, then run a Level 2 camera inspection to see whether the HeatShield surface has spalled or separated. If it’s intact, a clean flue is all you need. If it’s damaged, we’ll show you the photos and give you options. Call (833) 740-1407 to book an inspection.
Repeated freezing and thawing works on the bond between an ArmorFlex lining and the masonry flue wall. Exterior chimneys here see that cycling constantly through the cold months, and if water gets in behind the lining, freeze expansion causes cracking and separation at that bond. A properly installed lining with a watertight crown and flashing resists this. A lining with a cracked crown won’t. That’s why we check the crown and flashings on every HeatShield inspection in Berthoud.
A Level 2 inspection is the right call whenever a HeatShield lining is involved. A Level 1 visual check won’t show you what’s happening behind the lining surface or at the liner-to-flue bond. The Level 2 camera inspection does, and it gives you photo documentation you can keep for insurance or a home sale. We recommend Level 2 before any resurfacing or relining work. Call (833) 740-1407 for a free estimate.
Often yes, but only after the flue is checked against the appliance’s actual sizing and venting requirements. A stove or insert added to a flue that wasn’t sized for it produces continued creosote accumulation and stresses the lining. We look at the appliance, the flue dimensions, and the existing HeatShield surface together before anything goes in.
Spring hail and wind on tall, exposed exterior chimneys crack crowns repeatedly, and freeze-thaw cycles open those cracks wider. We repair crowns with HeatShield Crown Coat or Crown Repair products, which are formulated for masonry crowns and bond properly to the existing surface. A patch with generic mortar won’t hold through a Berthoud winter. Call (833) 740-1407 to get a crown assessment.
Service Areas Near Berthoud
We also serve homeowners in nearby Mead, Loveland, Fort Collins, Timnath, Windsor, Wellington, and Severance. If you’re on the edge of those areas and want to know whether we cover your address, give us a call and we’ll confirm before you book.
Book Your HeatShield Service in Berthoud Today
If your HeatShield lining hasn’t been looked at since the last burning season, or if a previous repair is giving you doubt, we’ll come out, inspect it properly, and hand you the photos. The estimate is free. Call (833) 740-1407. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Fort Collins.